2015年07月15日 15:26
NO.1 Refer to the exhibit.
Assuming that the peer is configured correctly and the interface is up, how many neighbors will be
seen in the EIGRPv6 neighbor table on this IPv6-only router?
A. one neighbor, which will use a local router-id of 6010. AB8. . /64
B. one neighbor, which will use a local router-id of 6020. AB8. . /64
C. none, because EIGRPv6 only supports authenticated peers
D. none, because of the mismatch of timers
E. none, because there is no EIGRP router ID configured
Answer: E
Cisco参考書勉強 400-101変更 400-101前提条件 400-101一発合格 400-101サンプル問題集
Explanation:
Configuring EIGRP for IPv6 has some restrictions; they are listed below: Reference.
http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routingprotocol-
eigrp/113267-eigrp-ipv6-00.html
NO.2 Refer to the exhibit.
What is the meaning of the asterisk (*) in the output?
A. PIM neighbor 10.1.5.6 is the RPF neighbor for the group 232.1.1.1 for the shared tree.
B. PIM neighbor 10.1.5.6 is the one that is seen as the RPF neighbor when performing the command
show ip rpf 10.1.4.7.
C. PIM neighbor 10.1.5.6 is the winner of an assert mechanism.
D. The RPF neighbor 10.1.5.6 is invalid.
Answer: C
Cisco日記 400-101勉強方法 400-101 400-101入門
Explanation:
show ip mroute Field Descriptions Field Description
RPF neighbor or RPF nbr IP address of the upstream router to the source. Tunneling indicates that
this router is sending data to the RP encapsulated in register packets. The hexadecimal number in
parentheses indicates to which RP it is registering. Each bit indicates a different RP if multiple RPs per
group are used. If an asterisk (*) appears after the IP address in this field, the RPF neighbor has been
learned through an assert. Reference.
http://www.cisco.com/c/en/us/td/docs/ios/12_2/ipmulti/command/reference/fiprmc_r/1rfmult3.ht
ml
NO.3 Refer to the exhibit.
You are bringing a new MPLS router online and have configured only what is shown to bring LDP up.
Assume that the peer has been configured in a similar manner. You verify the LDP peer state and see
that there are no neighbors. What will the output of show mpls ldp discovery show?
A. Interfaces: Ethernet0/0 (ldp): xmit
B. Interfaces: Ethernet0/0 (ldp): xmit/recv LDP Id: 25.25.25.2:0; IP addr: 192.168.12.2
C. Interfaces: Ethernet0/0 (ldp): xmit/recv LDP Id: 192.168.12.2:0; no route
D. Interfaces: Ethernet0/0 (ldp): xmit/recv LDP Id: 25.25.25.2:0; no route
Answer: D
Cisco 400-101体験 400-101日記 400-101全真問題集
NO.4 Which option is the Cisco recommended method to secure access to the console port?
A. Configure the activation-character command.
B. Configure a very short timeout (less than 100 milliseconds) for the port.
C. Set the privilege level to a value less than 15.
D. Configure an ACL.
Answer: A
Ciscoサンプル問題集 400-101一発合格 400-101難易度
Explanation:
The activation-character command defines a session activation character. Entering this character at a
vacant terminal begins a terminal session. The default activation character is the Return key To
secure the console port, you should change this character to a different one as most people simply
hit the enter key when trying to access the console.
NO.5 Which option is an incorrect design consideration when deploying OSPF areas?
A. area 1 - area 0 - MPLS VPN backbone - area 0 - area 2
B. area 1 - MPLS VPN backbone - area 2
C. area 1 - MPLS VPN backbone - area 1
D. area 2 - area 0 - MPLS VPN backbone - area 1
E. area 0 - area 2 - MPLS VPN superbackbone - area 1
Answer: E
Ciscoトレーニング費用 400-101予想試験 400-101試合
Explanation:
In the case of MPLS-VPN Backbone as The OSPF superbackbone behaves exactly like Area 0 in regular
OSPF, so we cannot have two different area 0's that are not directly connected to each other. When
area 0 connects to the superbackbone, it simply becomes an extension of area 0.
NO.6 Which statement describes the native VLAN concept in an ISL trunk?
A. It is the VLAN ID that is assigned to untagged packets.
B. It is the VLAN with highest priority.
C. It is the default VLAN for a trunk.
D. There is no native VLAN concept in an ISL trunk.
Answer: D
Cisco 400-101 400-101学習教材 400-101日本語版
Explanation:
ISL has no native VLAN concept because it places the entire ethernet frame in the payload of an ISL
frame. Native VLANs is an 802.1Q specific concept
NO.7 What is a reason to use DHCPv6 on a network that uses SLAAC?
A. To get a record of the IPs that are used by the clients
B. To push DNS and other information to the clients
C. No reason, because there is no need for DHCPv6 when using SLAAC
D. Because DHCPv6 can be used only in stateful mode with SLAAC to record the IPs of the clients
E. Because DHCPv6 can be used only in stateless mode with SLAAC to record the IPs of the clients
F. Because DHCPv6 is required to use first-hop security features on the switches
Answer: B
Cisco試験解答 400-101認定試験 400-101受験期 400-101資格 400-101入門
Explanation:
SLAAC is by far the easiest way to configure IPv6 addresses, simply because you don't have to
configure any IPv6 address. With SLAAC, a host uses the IPv6 Neighbor Discovery Protocol (NDP) to
determine its IP address and default routers. Using SLAAC, a host requests and listens for Router
Advertisements (RA) messages, and then taking the prefix that is advertised to form a unique address
that can be used on the network. For this to work, the prefix that is advertised must advertise a prefix
length of 64 bits (i.e., /64). But the most significant of Stateless Address Autoconfiguration (SLAAC) is
it provided no mechanism for configuring DNS resolver information.Therefore SLACC can be used
along with DHCPv6 (Stateless) to push DNS and other information to the clients.
NO.8 Which statement about the BGP originator ID is true?
A. The route reflector always sets the originator ID to its own router ID.
B. The route reflector sets the originator ID to the router ID of the route reflector client that injects
the route into the AS.
C. The route reflector client that injects the route into the AS sets the originator ID to its own router
ID.
D. The originator ID is set to match the cluster ID.
Answer: B
Cisco成果物 400-101勉強の資料 400-101ソリューション 400-101方法 400-101講座
Explanation:
An RR reflecting the route received from a RR-Client adds:
Reference. https://sites.google.com/site/amitsciscozone/home/bgp/bgp-route-reflectors
ずっと自分自身を向上させたいあなたは、400-101認定試験を受験する予定があるのですか。もし受験したいなら、試験の準備をどのようにするつもりですか。もしかして、自分に相応しい試験参考書を見つけたのでしょうか。では、どんな参考書は選べる価値を持っていますか。あなたが選んだのは、Pass4Testの400-101問題集ですか。もしそうだったら、もう試験に合格できないなどのことを心配する必要がないのです。
しかし、400-101「CCIE Routing and Switching Written Exam v5.0」試験は簡単ではありません。専門的な知識が必要で、もしあなたはまだこの方面の知識を欠かれば、Pass4Testは君に向ける知識を提供いたします。Pass4Testの専門家チームは彼らの知識や経験を利用してあなたの知識を広めることを助けています。そしてあなたに400-101試験に関するテスト問題と解答が分析して差し上げるうちにあなたのIT専門知識を固めています。
Pass4TestのITの専門研究者はCisco 400-101認証試験の問題と解答を研究して、彼らはあなたにとても有効な訓練試験オンラインサービスツールを提供します。もしあなたはPass4Testの製品を購入したければ弊社が詳しい問題集を提供して、君にとって完全に準備します。弊社のPass4Test商品を安心に選択してPass4Test試験に100%合格しましょう。
Pass4Testが提供した商品の品質が高く、頼られているサイトでございます。購入前にネットで部分な問題集を無料にダウンロードしてあとで弊社の商品を判断してください。Pass4Testは君の試験に１００％の合格率を保証いたします。迷ってないください。
君はまずネットで無料なCiscoの400-101試験問題をダウンロードしてから 弊社の品質を確信してから、購入してください。Pass4Testは提供した商品は君の成功を全力で助けさしたげます。
Ciscoの400-101認定試験に受かるのはあなたの技能を検証することだけでなく、あなたの専門知識を証明できて、上司は無駄にあなたを雇うことはしないことの証明書です。当面、IT業界でCiscoの400-101認定試験の信頼できるソースが必要です。Pass4Testはとても良い選択で、400-101の試験を最も短い時間に縮められますから、あなたの費用とエネルギーを節約することができます。それに、あなたに美しい未来を作ることに助けを差し上げられます。
弊社のCiscoの400-101勉強資料を利用したら、きっと試験を受けるための時間とお金を節約できます。Pass4TestのCiscoの400-101問題集を買う前に、一部の問題と解答を無料にダウンロードすることができます。PDFのバージョンとソフトウェアのバージョンがありますから、ソフトウェアのバージョンを必要としたら、弊社のカスタマーサービススタッフから取得してください。
Pass4Testは最新の4A0-104試験問題集と高品質のVCI510認定試験の問題と回答を提供します。Pass4TestのC2020-013 VCEテストエンジンとCV0-001試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質の70-680トレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100％保証します。試験に合格して認証資格を取るのはそのような簡単なことです。
記事のリンク：http://blog.vmware-certified-professional.com/?p=21675